To solve this problem, meet the installation requirements, the re installation, in order to maintain the vertical and horizontal strictly, center line level and check the base in an annular processing line on the surface of the base, the base is adjusted by adjusting the wedge level, will tighten the anchor screws, second two. When the Grouting grouting layer after hardening, remove the adjusting wedge iron from the crusher base, and cement filling this gap, and then according to the standard installation frame check. Install the drive shaft, the adjusting shim body base and shaft bracket flange between the reduction pinion move along the axial direction 10mm, the size of cone gear Face alignment, so that the big gear must be increased to ensure two gear meshing clearance, and increase the shim under the eccentric sleeve, setting good gear position, side clearance measured two gear 1.88mm. installed in the bowl type bearing frame, found the bowl type bearing frame bottom and large conical gear top (Fig. 1 in the A plane) interfere with the hand disc drive shaft coupling, can hear the bowl type bearing frame and the bottom surface of the big bevel gear at the top of a friction sound. To continue the installation of cone crushing, the measured gap spindle and tapered bushing is 1.52mm, open the inspection of each component, can use, and meet the requirements, which will great circle The counterweight side bevel gear (Fig. 1 A) to reduce the height of 5mm and a ring gasket contact surface between the frame and the frame of bowl bearing, 6 mm thick, mounted crushing cone, the measured gap spindle and tapered bushing 1.86mm.
The crushing cone and spherical bearings, crushing cone and cone copper sleeve, eccentric sleeve and body copper sleeve and other friction surfaces subject to great pressure lubrication is important for crusher. The machine adopts oil lubrication system, divided into the lubricating oil inside the machine. One from the lower part of the machine oil alone L enter the machine after the air inside and outside surface of the eccentric shaft respectively reach 3 branches, the middle of the main shaft oil hole to the bowl through the pore size of gear bearing, lubrication, and then by the small bevel gear at the lower part of the oil return hole oil return. Another is composed of a drive shaft on the frame hole into the oil, lubricating oil to the transmission bearing. Also through the oil return hole at the lower part of the small bevel gear and anti The oil return holes on the dust cap return oil. The oil returns to the oil tank from a single pipeline. When the heavy oil is reloaded, the lubricating system is cleaned thoroughly, the oil circuits are cleared, and the lubricating oil is replaced completely
After repeated inspection, cone crusher with the size of the installation requirements. With the hand disc drive shaft coupling, light and no blocking phenomenon. Start the pump, adjust the safety valve, the hydraulic stability in 1.1k g / cm, the oil flow is stable after the no-load start, idle test continuous operation of about 2 h, crushing cone from around the center line of rotation speed is 13R / min. ore after crushing cone bevel gear is reversed, no periodic noise. At the same time, other parameters showed normal operation. Using the crusher crusher since 4 A has not broken teeth accidents, ensure the normal production of the concentrator. From a single The machine gear and related accessories consumption, saving cost is close to l0 yuan
Introduction of cone crusher parts
Hunan Fengwei Wear Parts Foundry, specializing in the production of domestic and foreign brands of crusher wear spare parts manufacturers, production of domestic brands, Hua Yang, Shan Bao, SBM brands such as crusher wear parts, spare parts, as well as foreign brands, Metso, Sandvik, TEREX and other import brands crusher spare parts, wear parts, mining quarry companies such as crusher wear parts of choice. We achieve cost-effective localization of imported spare parts, service users at home and abroad. The company can be matched with various brands of hydraulic crusher electric parts, sealing parts, standard parts and other accessories, can meet the needs of one-stop shopping for customers at home and abroad the demand.
Hunan Fengwei Wear Parts Foundry has thirty years of production experience, and years of experience in processing export products, products have been exported to the United States, Canada, Australia, Sweden, Finland, Russia, Ukraine and Southeast Asia and other countries and regions. Hunan Fengwei Wear Parts Foundry product using the original material, high-quality raw materials, casting and heat treatment process we have a unique thirty years production experience, to ensure complete interchangeability, and original spare parts with high quality and competitive price, provide quality products, quality services for the majority of users.
Hunan Fengwei Wear Parts Foundry wearable parts can be customized to map, and if there is no map, the company has professional mapping personnel to help you mapping, after customization
Contact:Sales Director: Eileen Cai ;
Email: sales@hnfwe.com;
Mobile telephone: +8618692872223