Objective: as we all know, the crusher is used for crushing the bulk material. These devices are very focused on maintenance. Maintenance is done well, can greatly improve the efficiency of production machinery and mechanical life. The crusher maintenance technology. I think we all know crusher maintenance technology with the seasons is different. With the advent of winter, you know how in the winter maintenance crusher?
- cleaning of crusher
Crushing machine cleaning diesel engine, chassis, working device appearance can play a role in cleaning decontamination and cleaning process can also be found that the device components damage and leakage of parts, the preparatory work for the next maintenance. Prohibit the use of high pressure and high temperature water to wash water requirements of high position, especially is the electrical part, so as to avoid damage.
Selection and replacement of broken lubricating oil
Selection of fuel oil
Diesel oil at a low temperature, easy to wax, higher viscosity, poor liquidity, poor atomization, the combustion process of deterioration, reduces the power and economy of diesel engine. In order to make the engine work soft, reduce fuel consumption, should choose low pour point diesel. The general selection principle is: diesel oil pour point than the environment mixed degree of 5 DEG C lower. For the winter diesel grades are: -10#, -20#, -35# etc. maintenance, clean fuel system. Thorough cleaning of all filters, fuel filter, oil water separator and sewage discharge cleaning, and check the oil pump work, to eliminate hidden faults.
Replacement of diesel engine oil
Diesel oil used should be low viscosity small. Try to use high performance oil, this oil not only at high temperature is not easy oxidation, but does not leave sediments in precision parts of the diesel engine, can prolong the service life of the diesel oil. Multistage can work in a wide temperature range, generally optional viscosity grade level oil of SAE5W-40 or SAE10W-40. The replacement of oil and oil filter should be replaced or cleaned.
Replace lubricating oil and grease
Seasonal maintenance, transmission, sub actuators, differential change gear oil for winter gear within the oil to the oil, pay attention to cleaning.
- crushing machine maintenance
Cooling system of diesel engine maintenance check thermostat working state, prevent the diesel engine water temperature is too low or too high in the water jacket. Remove scale. To select below the crusher areas using the minimum temperature of 10 degrees Celsius, with summer winter frost, anti boiling, anti-corrosion, antifreeze waterproof scale. If it is found that the mud and sand tank deposit, immediately removed.
Maintenance of electrical equipment, check the motor wiring of the battery, check and adjust the electrolyte density, maintain the starting motor, adjust the charging voltage of the generator, charge the battery regularly in winter and maintain the preheating device
Brake system maintenance Note brake fluid is sufficient. The quality is bad. Check the oil and water separator. A dirt discharging switch is working properly. Check the brake is not weak, deviation, brake pedal pedal and brake to insufficient phenomenon, timely adjustment.
Introduction of cone crusher parts
Hunan Fengwei Wear Parts Foundry, specializing in the production of domestic and foreign brands of crusher wear spare parts manufacturers, production of domestic brands, Hua Yang, Shan Bao, SBM brands such as crusher wear parts, spare parts, as well as foreign brands, Metso, Sandvik, TEREX and other import brands crusher spare parts, wear parts, mining quarry companies such as crusher wear parts of choice. We achieve cost-effective localization of imported spare parts, service users at home and abroad. The company can be matched with various brands of hydraulic crusher electric parts, sealing parts, standard parts and other accessories, can meet the needs of one-stop shopping for customers at home and abroad the demand.
Hunan Fengwei Wear Parts Foundry has thirty years of production experience, and years of experience in processing export products, products have been exported to the United States, Canada, Australia, Sweden, Finland, Russia, Ukraine and Southeast Asia and other countries and regions. Hunan Fengwei Wear Parts Foundry product using the original material, high-quality raw materials, casting and heat treatment process we have a unique thirty years production experience, to ensure complete interchangeability, and original spare parts with high quality and competitive price, provide quality products, quality services for the majority of users.
Hunan Fengwei Wear Parts Foundry wearable parts can be customized to map, and if there is no map, the company has professional mapping personnel to help you mapping, after customization
Contact:Sales Director: Eileen Cai ;
Email: sales@hnfwe.com;
Mobile telephone: +8618692872223